Ryobi Outdoor RPBV2500 User Manual download pdf (Page 2)

AIR DEFLECTOR Fig 6

Hook tabs 1 & 2, 3, 4, and 5 (in that order) onto blower

housing through slots. Make sure all 5 tabs are secured

onto housing.

Push down and in simultaneously on air deflector to lock

into place.

OIL & FUEL MIXTURE

Thoroughly mix 200ml of 2 stroke oil to 5 litres of unlead-

ed petrol in a container and fill the trimmer fuel tank. Fig

7. Care should be taken not to overfill the fuel tank which

will result in fuel splashing onto engine parts.

WARN-

ING:

Always

stop the

motor and allow

it to cool before re-filling the fuel tank. Failure

to adhere to this warning can result in vapour

explosion causing serious personal injury.

WARNING: Always mix petrol and oil in a sepa-

rate container. Do not mix directly in the trim-

mer fuel tank which will cause motor damage

and void the warranty.

WARNING

If the machine becomes clogged,

under no circumstances should you

attempt to remove blockage from the

impeller with your hands.

To remove blockage, stop the motor

and remove the Dust Bag and Tubes.

Remove any debris from the impeller

with a stick. Failure to adhere to this

warning can and will result in serious

personal injury.

STARTING & STOPPING INSTRUCTIONS

Place blower on the ground. Fully depress and release the

primer bulb 5 to 7 times. Fuel should be visible in the

bulb. Fig 8

Place the choke lever in the “Full Choke” (position 1). Fig

Squeeze throttle trigger fully and pull the starter rope

briskly until the motor sounds like it wants to start. Fig 10.

Move the choke lever to “Partial Choke” (position 2).

Squeeze throttle trigger fully and pull starter rope until the

motor starts.

Run motor approx. 30 seconds at full throttle before mov-

ing the choke lever to “Run” (position 3)

Fig 6

Fig 8

Fig 7

Fig 9

Fig 10

Fuel

Tank

Primer Bulb

Full

Choke

Partial

Choke

Run

Starter Rope

Air Deflector

1&2

Throttle

Trigger

n ASSEMBLY

BLOWER TUBES Turn nozzle clockwise to screw into

blower tube. Turn nozzle and tube clockwise to screw into

blower until tight Fig 1. Your machine is now ready for

blowing applications

CONVERTING BLOWER

TO VACUUM

Using a flat screwdriver,

loosen the locking screw

to open vacuum inlet cover

Fig 2.

Align the 4 locking bosses

in inlet housing with slots

in upper vacuum tube.

Push vacuum tubes into

housing and turn clockwise

to lock in place. Fig 3

ATTACH VACUUM BAG

Remove nozzle from blower tube. Install vacuum bag over

blower tube, ensuring the end of the bag sleeve is com-

pletely covering the rib in the blower tube. Fig 4 & 5

Wrap fastening strap tightly around the blower tube and

through the fastening loop. Rotate vacuum bag until

shoulder strap is upright and ensure that the bag is zipped

closed before starting the machine.

RULES FOR SAFE OPERATION

The purpose of safety rules is to attract your attention to

possible dangers. The safety symbols and the explanations

with them, require your careful attention and understanding.

The safety warnings do not by themselves eliminate any dan-

ger. The instruction or warnings they give are not substitutes

for proper accident prevention measures.

SAFETY ALERT SYMBOL. Indicates caution or

warning. May be used in conjunction with other

symbols or pictures.

WARNING: Failure to obey a safety warning can

result in serious injury to yourself or to others.

Always follow the safety precautions to reduce

the risk of fire, electric shock and personal injury.

WARNING: Do not attempt to operate this tool

until you have read thoroughly and understood

completely, safety rules, etc. contained in this

manual. Failure to comply can result in accidents

involving fire, electric shock or serious personal

injury. Save owners manual and review frequent-

ly for continuing safe operation and instructing

others who may use this tool.

The operation of any tool can result in

foreign objects being thrown into your

eyes, which can result in severe eye

damage. Before beginning power tool

operation, always wear safety goggles

or safety glasses with side shields and a

full face shield when needed. We recommend Wide

Vision Safety Mask for use over eyeglasses or standard

safety glasses with side shields.

1. KNOW YOUR POWER TOOL. Read owners manual

carefully. Learn its applications and limitations as well as

the specific potential hazards related to this tool.

2. GUARD AGAINST ELECTRICAL SHOCK BY

PREVENTING BODY CONTACT WITH GROUNDED

SURFACES. For example, pipes, radiators, ranges,

refrigerator enclosures.

3. KEEP WORK AREA CLEAN. Cluttered areas and

benches invite accidents.

4. AVOID DANGEROUS ENVIRONMENT. Don't use

power tools in damp or wet locations or expose to rain.

Keep work area well lit.

5. KEEP CHILDREN AND VISITORS AWAY. Visitors should

wear safety glasses and be kept a safe distance from work

area. Do not let visitors contact tool or extension cord.

6. STORE IDLE TOOLS. When not in use, tools should be

stored in a dry and high or locked-up place, out of reach

of children.

7. DON'T FORCE TOOL. It will do the job better and safer

at the rate at which it was designed.

8. USE RIGHT TOOL. Don't force small tool or attachment

to do the job of a heavy duty tool. Don't use tool for

purpose not intended.

9. DRESS PROPERLY. Do not wear loose clothing or

jewellery. They can be caught in moving parts or sucked

into the machine. Rubber gloves and non-skid footwear

are recommended when working outdoors. Also wear

protective hair covering to contain long hair.

10. ALWAYS WEAR SAFETY GLASSES. Everyday

eyeglasses have only impact resistant lenses, they are

not safety glasses.

11. PROTECT YOUR LUNGS. Wear a dust mask if

operation is dusty.

12. PROTECT YOUR HEARING. Wear hearing protection

during extended periods of operation.

13. DON'T OVERREACH. Keep proper footing and balance

at all times. Do not use tool on a ladder or unstable

support. Secure tools when working at elevated levels.

14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and

clean for better and safer performance. Follow

instructions for lubricating and changing accessories.

15. REMOVE ADJUSTING KEYS AND WRENCHES. Form a

habit of checking to see that keys and adjusting

wrenches are removed from tool before turning it on.

16. NEVER USE IN AN EXPLOSIVE ATMOSPHERE.

Normal sparking of the motor could ignite fumes.

17. KEEP HANDLES DRY, CLEAN AND FREE FROM OIL

AND GREASE. Always use a clean cloth when

cleaning. Never use brake fluids, gasoline, petroleum

based products, or any strong solvents to clean your tool.

18. STAY ALERT AND EXERCISE CONTROL. Watch what

you are doing and use common sense. Do not operate

tool when you are tired. Do not rush.

19. CHECK DAMAGED PARTS. Before further use of the

tool, a guard or any other part that is damaged should

be carefully checked to determine that it will operate

properly and perform its intended function. Check for

alignment of moving parts, binding of moving parts,

breakage of parts, mounting and any other conditions

that may affect its operation. A guard or any other part

that is damaged should be properly repaired or replaced

by an authorised service centre.

20. DO NOT USE TOOL IF SWITCH DOES NOT TURN IT

ON AND OFF. Have defective switches replaced by

authorised service centre.

21. DO NOT OPERATE THIS TOOL WHILE UNDER THE

INFLUENCE OF DRUGS, ALCOHOL OR ANY

MEDICATION.

SAVE THESE INSTRUCTIONS

FOR FUTURE REFERENCE

Due to Ryobi's continued product refinement poli-

cy,product features and specifications can and will

change without notice. Check current features and

specifications with your Ryobi retailer.

Handle

Throttle Trigger

Stop

Switch

Fuel Tank

Primer Bulb

Fig 1

Fig 2

Fig 3

Upper

Vacuum

Tube

Vacuum

Tube

Fig 5

Fig 4

Nozzle

Blower Tube

Blower

Tube

Rib

Blower

Tube

Vacuum

Bag

Vacuum Inlet

Cover

Locking

Screw

Blower

Tube

Nozzle

Starter

Rope

Choke

Lever

Vacuum

Inlet Cover

Locking

Bosses

Full

Choke

Partial

Choke

CHOKE POSITIONS

Run

P 2

P 3

P 4

1 2

Comments to this Manuals

No comments

Ryobi Outdoor RPBV2500 User Manual Page 2

Comments to this Manuals